Scorpion Jacks
We give the best Services
Scorpion Jacks are the most advanced service/floor jacks available today. Our jacks are the only jacks available with a built in lock assembly eliminating the need for vehicle stands. Two points of contact when lifting and an upright posture for the technician. Scorpion Jacks are the Ultimate Jack for any Heavy-Duty truck service shop.
Scorpion TJ12S
WHAT MAKES THIS NEW PATENTED JACK SO REVOLUTIONARY?
The Scorpion TJ12S lifts the whole front end or rear end in one go! A conventional jack you have to lift a corner at a time.
The Scorpion TJ12S is the only jack available with a built in three stage locking mechanism so there is no need for vehicle stands!
The Scorpion TJ12S is built to last and is made of the highest grade materials!
THE RESULT IS?
Increased through-put for your shop. The TJ12S lifts a truck in seconds! A conventional jacks and two stand takes 7-10 minutes!
Reduce employee fatigue and injuries. The TJ12S keeps your technicians off the floor as much as possible keeping them fresh and alert for the servicing of vehicles. You preserve your hard earned money buy not throwing it away on jacks that don’t last
HOW DOES IT WORK?
The Scorpion TJ12S has a vertical handle and four full floating casters. The vertical handle provides a more comfortable posture for the technician. The casters make it extremely manouverable.
It has dual hydraulic cylinders that do the lifting all controlled by detachable remote control pendant. Everything is pneumatically controlled. There is only one button to lift and one button to lower. It’s that easy.
To lift you simply lower the handle assembly and push the jack under the truck to the axle. For rear axles you can extend the handle up to 9 Ft. to get to the axle without getting on the floor. Then depress the up button and the jack raises the truck across the axle. Stop at any time the lock will engage automatically.
To lower the truck simply raise the jack slightly and then depress the down button and the truck is lowered safely.
Features
24,000 lb. Capacity or 12 Tons
Only 7.5” collapsed height to go under the lowest axles
Two Point of contact when lifting, safer!
Air/Hydraulic Design, NO HAND PUMPING REQUIRED
Lifts over 19” with a built in 3 stage safety lock!
(No need for vehicle stands) WOW!
Full floating casters for easy maneuvering
Small foot print doesn’t take up much floor space
Scorpion TJ12SL
24,000 Lb. Cap Floor Service Jack LOW PROFILE
The Scorpion Tj12S is a revolutionary floor service jack for the truck repair industry. 24,000 lb. Cap or 12 Ton
WHATS MAKES THIS NEW PATENTED JACK SO REVOLUTIONARY?
The Scorpion TJ12SL lifts the whole front end or rear end in one go! A conventional jack you have to lift a corner at a time.
The Scorpion TJ12SL is the only jack available with a built in three stage locking mechanism so there is no need for vehicle stands!
The Scorpion TJ12SL is built to last and is made of the highest grade materials!
THE RESULT IS?
Increased through-put for your shop. The TJ12SL lifts a truck in seconds! A conventional jacks and two stand takes 7-10 minutes!
Reduce employee fatigue and injuries. The TJ12SL keeps your technicians off the floor as much as possible keeping them fresh and alert for the servicing of vehicles. You preserve your hard earned money buy not throwing it away on jacks that don’t last
HOW DOES IT WORK?
The Scorpion TJ12SL has a vertical handle and four full floating casters. The vertical handle provides a more comfortable posture for the technician. The casters make it extremely manouverable.
It has dual hydraulic cylinders that do the lifting all controlled by detachable remote control pendant. Everything is pneumatically controlled. There is only one button to lift and one button to lower. It’s that easy.
To lift you simply lower the handle assembly and push the jack under the truck to the axle. For rear axles you can extend the handle up to 9 Ft. to get to the axle without getting on the floor. Then depress the up button and the jack raises the truck across the axle. Stop at any time the lock will engage automatically.
To lower the truck simply raise the jack slightly and then depress the down button and the truck is lowered safely.
Features:
24,000 lb. Capacity or 12 Tons
Only 7.5” collapsed height to go under the lowest axles
Two Point of contact when lifting, safer!
Air/Hydraulic Design, NO HAND PUMPING REQUIRED
Lifts over 19” with a built in 3 stage safety lock!
(No need for vehicle stands) WOW!
Full floating casters for easy maneuvering
Small foot print doesn’t take up much floor space
TJ14
Scorpion TJ14, 28,000 Lb. Cap Floor Service Jack
The Scorpion Tj14 is a revolutionary floor service jack for the truck repair industry. 28,000 lb. Cap or 14 Ton
WHATS MAKES THIS PATENTED JACK SO REVOLUTIONARY?
1. The Scorpion TJ14 lifts the whole front end or rear end in one go! A conventional jack you have to lift a corner at a time.
2. The Scorpion TJ14 is the only jack available with a built in three stage locking mechanism so there is no need for vehicle stands!
3. The Scorpion TJ14 is built to last and is made of the highest grade materials!
THE RESULT IS?
1. Increased through-put for your shop. The TJ14 lifts a truck in seconds! A conventional jacks and two stand takes 7-10 minutes!
2. Reduce employee fatigue and injuries. The TJ14 keeps your technicians off the floor as much as possible keeping them fresh and alert for the servicing of vehicles.
3. You preserve your hard earned money buy not throwing it away on jacks that don’t last.
Scorpion Installed Tire Service Lifts
Models: TJ12AG Above Ground – TJ12SG Semi-In-ground – TJ12IG In-Ground
The Scorpion Installed Tire service lifts are an ideal solution for those shops that perform a lot of tire service and Brake Service. This is an installed version of the ScorpionTJ12 model service jack and it offers a perfect combination of speed, effeciency, ease of use and value. The Scorpion Installed lifts are much less expensive than your standard above-ground options or for that matter the in-ground options too. Most of which are over $20,000.00 WOW!
The Scorpion installed lifts are under $10,000.00 That’s great value.
These jacks are designed to lift the vehicle across the axle using the lifting saddles provided (Low/Med/Hi)
There is a built in lock for safety and other convenience features.
The lifts come with a control station housing the pump unit and a 20 Ft. Remote control so the operator can spot the load.
Features;
- 25,000 Lb. Cap
- Dual Hydraulic rams for lifting
- Lift over 20” with a built in safety lock
- Lift across the axle with the lifting saddles or lift on the frame!
- Heavy-Duty Hydraulics and air motor
Spec Sheets:
TJ12AG Above Ground
TJ12SG Semi-In-ground
TJ12IG In-Ground
Scorpion Pit Jacks
Models: Scorpion PJ15 – PJ25
Scorpion Pit Jacks (Truck & Bus Service Pits & Alignment Ramps)
The Scorpion PJ15 and PJ25 Pit Jacks are designed for use in Heavy Truck service pits or can also be used on above ground alignment ramp systems (HUNTER & BEE-LINE). These jack will fit virtually any pit application due to their compact design only (34” wide) and expandable up to 42” wide. These jacks are designed to lift the vehicle across the axle using the lifting saddles provided (Low/Med/Hi) There is a built in lock for safety and other convenience features.
Features:
- 15,000 Lb. Cap or 25,000 Lb. Cap
- Dual Hydraulic ramps for lifting
- Lift over 20” with a built in safety lock
- Lift across the axle with the lifting saddles or lift on the frame!
- Heavy-Duty Hydraulics and air motor
- Special roller bearing wheels allow for effortless rolling
PJ12S
The Scorpion PJ12S Pit Jack is designed for use in Heavy Truck service pits or can also be used on above ground alignment ramp systems (HUNTER & BEE-LINE).
These jack will fit virtually any pit application due to their compact design only (31” wide) and expandable up to 46” wide.
These jacks are designed to lift the vehicle across the axle using the lifting saddles provided (Low/Med/Hi)
There is a built in lock for safety and other convenience features.
Features:
- 12,000 Lb. Cap
- Telescoping arms for wide pick up points
- Lift over 20” with a built in safety lock
- Convenient pull handle, powder coat paint & zinc plated components
- Lift across the axle with the lifting saddles or lift on the frame!
- Heavy-Duty Hydraulics and air motor
- Special roller bearing wheels allow for effortless rolling
PJ15
The Scorpion PJ15 Pit Jack is designed for use in Heavy Truck service pits or can also be used on above ground alignment ramp systems (HUNTER & BEE-LINE).
These jack will fit virtually any pit application due to their compact design only (34” wide) and expandable up to 42” wide.
These jacks are designed to lift the vehicle across the axle using the lifting saddles provided (Low/Med/Hi)
There is a built in lock for safety and other convenience features.
Features:
- 15,000 Lb. Cap
- Dual Hydraulic rams for lifting
- Lift over 20” with a built in safety lock
- Convenient pull handle, powder coat paint & zinc plated components
- Lift across the axle with the lifting saddles or lift on the frame!
- Heavy-Duty Hydraulics and air motor
- Special roller bearing wheels allow for effortless rolling
PJ15S
The Scorpion PJ15S Pit Jack is designed for use in Heavy Truck service pits or can also be used on above ground alignment ramp systems (HUNTER & BEE-LINE).
These jack will fit virtually any pit application due to their compact design only (31” wide) and expandable up to 46” wide.
These jacks are designed to lift the vehicle across the axle using the lifting saddles provided (Low/Med/Hi)
There is a built in lock for safety and other convenience features.
Features:
- 15,000 Lb. Cap
- Telescoping arms for wide pick up points
- Lift over 20” with a built in safety lock
- Convenient pull handle, powder coat paint & zinc plated components
- Lift across the axle with the lifting saddles or lift on the frame!
- Heavy-Duty Hydraulics and air motor
- Special roller bearing wheels allow for effortless rolling
PJ25
The Scorpion PJ25 Pit Jack is designed for use in Heavy Truck service pits or can also be used on above ground alignment ramp systems (HUNTER & BEE-LINE).
These jack will fit virtually any pit application due to their compact design only (34” wide) and expandable up to 42” wide.
These jacks are designed to lift the vehicle across the axle using the lifting saddles provided (Low/Med/Hi)
There is a built in lock for safety and other convenience features.
Features:
- 25,000 Lb. Cap
- Telescoping arms for wide pick up points
- Lift over 20” with a built in safety lock
- Convenient pull handle, powder coat paint & zinc plated components
- Lift across the axle with the lifting saddles or lift on the frame!
- Heavy-Duty Hydraulics and air motor
- Special roller bearing wheels allow for effortless rolling
PJ25S
The Scorpion PJ25S Pit Jack is designed for use in Heavy Truck service pits or can also be used on above ground alignment ramp systems (HUNTER & BEE-LINE).
These jack will fit virtually any pit application due to their compact design only (32” wide) and expandable up to 46” wide.
These jacks are designed to lift the vehicle across the axle using the lifting saddles provided (Low/Med/Hi)
There is a built in lock for safety and other convenience features.
Features:
- 25,000 Lb. Cap
- Dual Hydraulic rams for lifting
- Lift over 20” with a built in safety lock
- Convenient pull handle, powder coat paint & zinc plated components
- Lift across the axle with the lifting saddles or lift on the frame!
- Heavy-Duty Hydraulics and air motor
- Special roller bearing wheels allow for effortless rolling
PJ35S
The Scorpion PJ35S Pit Jack is designed for use in Heavy Truck service pits or can also be used on above ground alignment ramp systems (HUNTER & BEE-LINE).
These jack will fit virtually any pit application due to their compact design only (32” wide) and expandable up to 46” wide.
These jacks are designed to lift the vehicle across the axle using the lifting saddles provided (Low/Med/Hi)
There is a built in lock for safety and other convenience features.
Features:
- 35,000 Lb. Cap
- Telescoping arms for wide pick up points
- Lift over 20” with a built in safety lock
- Convenient pull handle, powder coat paint & zinc plated components
- Lift across the axle with the lifting saddles or lift on the frame!
- Heavy-Duty Hydraulics and air motor
- Special roller bearing wheels allow for effortless rolling
Scorpion MJ25
Military Floor Service Jack
- 25,000 Lb. Cap 12.5 tons
- Extendable lifting beam with stackable adapters for all military vehicle applications
- Two points of contact when lifting, safer!
- Air/hydraulic design no pumping required
- Lifts over 36” with a built in safety lock!
(No need for vehicle stands!) WOW! - Full floating casters for easy maneuvering
- Very small foot print doesn’t take up much room
- A selection of three different saddles low/med/high
- Saddle storage right on the jack!
- Comfortable control handle extends up to 9 Ft.
- Detachable remote control (great for spotting your load)
Scorpion TJ12E
12 Ton or 24,000 Lb. Cap. End Lift/ Bumper Jack for heavy trucks
The TJ12E lifts the whole front end or rear end in one go. However in this case we are lifting on the frame of the truck or on the bumper of the truck.
The TJ12E has all the features of the TJ12S, including the three stage safety lock. The top section has been changed to include two extendable arms that can reach out to wider pick up points. Also included are stacking lifting adapters that allow you to adjust the pick up height for the various pick up points.